Caterpillar Engines Troubleshooting

Cat Engines Maintenance & Repair Guides

Skip to content
Menu
  • Home
  • About Me
  • Contact Us
  • Privacy Policy

Tag: C15

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0273 FMI 04 Turbo Outlet Pressure short to ground

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: The signal voltage for the turbocharger outlet pressure sensor falls below 0.5 VDC for two seconds. System Response: The Electronic…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0273 FMI 03 Turbo Outlet Pressure open/short to +

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: With an engine speed of zero rpm, the signal voltage for the turbocharger outlet pressure sensor exceeds 4.95 VDC for…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0273 FMI 00 Turbo Outlet Pressure above normal

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: The Electronic Control Module (ECM) detects all of the following conditions: The outlet pressure of the turbocharger is greater than…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0268 FMI 02 Check Programmable Parameters

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: The Electronic Control Module (ECM) detects that one or more of the programmable parameters have not been programmed. System Response:…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0263 FMI 04 Digital Sensor Supply short to ground

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: The Electronic Control Module (ECM) detects supply voltage that is below normal. System Response: The ECM will log the diagnostic…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0263 FMI 03 Digital Sensor Supply short to +batt

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: The Electronic Control Module (ECM) detects supply voltage that is above normal. System Response: The ECM will log the diagnostic…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0262 FMI 04 5 Volt Sensor DC Power Supply short t

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: The 5 volt sensor supply voltage drops below normal. System Response: The Electronic Control Module (ECM) logs the diagnostic code.…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0262 FMI 03 5 Volt Sensor DC Power Supply short t

Posted on April 4, 2022 by sam

Conditions Which Generate This Code: The voltage level of the 5 volt supply is above normal. System Response: The Electronic Control Module (ECM) will log…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0261 FMI 13 Engine Timing Calibration required

Posted on April 1, 2022 by sam

Conditions Which Generate This Code: The timing has not been calibrated since the Electronic Control Module (ECM) was installed or the calibration is incorrect. System…

C15

C-10, C-12, C-15 and C-16 Industrial Engines – CID 0254 FMI 12 Electronic Control Module Error

Posted on April 1, 2022 by sam

Conditions Which Generate This Code: The Electronic Control Module (ECM) has detected an internal fault. System Response: The ECM will log the diagnostic code. Engine…

Posts pagination

Previous Page Page 1 … Page 11 Page 12 Page 13 … Page 19 Next Page

Resources

  • About Me
  • Contact Us
  • Privacy Policy

Categories

  • 3126
  • 3126
  • 3208
  • 3306
  • 3406E
  • BX-2150
  • C15
  • C18
  • C7
  • Cat ID
  • D330
  • Delco 27SI
  • EL-740
  • Engine News
  • Programming
  • Service Magazine
  • Special Instruction
  • Troubleshooting
  • Uncategorized

Recent Posts

  • Cat C7 Injection Actuation Pressure Sensor Location
  • Programming – A/C Pressure Switch Fan-On Time
  • Programming – Minimum & Maximum Idle Shutdown Outside Temperature
  • Programming – Allow Idle Shutdown Override
  • Programming – Idle Shutdown Timer
© Copyright 2026 – Caterpillar Engines Troubleshooting
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy