Caterpillar Engines Troubleshooting

Cat Engines Maintenance & Repair Guides

Skip to content
Menu
  • Home
  • About Me
  • Contact Us
  • Privacy Policy

Author: sam

3208

3208 INDUSTRIAL ENGINE – Indicators For Water Temperature Electric

Posted on March 4, 2022 by sam

5L7446 Indicator 12V; Use With 2N1311 Sending Unit Range … 38 to 116°C (100 to 240°F) Test voltage … 14V 5L7444 Indicator 24V; Use With…

3208

3208 INDUSTRIAL ENGINE – Ammeters

Posted on March 4, 2022 by sam

1W8914 Indicator Illustrated 1W8914 And 1W8915 Indicator

3208

3208 INDUSTRIAL ENGINE – Indicators For Engine Oil Pressure

Posted on March 4, 2022 by sam

Electric 1W7143 Indicator 24V; Use With 302010 Sending Unit 6N0673 Indicator 24V; Use With 302010 Sending Unit 2N0781 Indicator 12V; Use With 2N0782 Sending Unit…

3208

3208 INDUSTRIAL ENGINE – Gauge For Water Temperature 5L7446 Gauge; Use with 2N1311 Sending Unit.

Posted on March 4, 2022 by sam

Rating … 12V Temperature range … 100 to 240°F(38 to 115°C) Calibration test at 14V (30° mounting): 100°F (38°C) … 348.7 Ohms 170°F (77°C) ……

3208

3208 INDUSTRIAL ENGINE – Oil Pump

Posted on March 3, 2022 by sam

NOTE: The relief valve guide is a housing where spring (3) is located. Tighten relief valve guide to a torque of … 40 ± 7…

3208

3208 INDUSTRIAL ENGINE – Oil Pump

Posted on March 3, 2022 by sam

NOTE: Tighten relief valve guide to … 30 ± 5 lb.ft.(40 ± 7 N·m) (1) Front housing assembly. (2) Oil pump cover assembly. (3) 1W1788…

3208

3208 INDUSTRIAL ENGINE – Gauge For Engine Oil Pressure 2N781 Gauge; Use with 2N782 Sending Unit.

Posted on March 3, 2022 by sam

Rating … 12V Pressure range … 0 to 120 psi(0 to 830 kPa) Calibration test at 14V (30° mounting): 0 psi (0 kPa) … 240…

3208

3208 INDUSTRIAL ENGINE – Oil Level Gauge

Posted on March 3, 2022 by sam

Remove & Install Oil Level Gauge 1. Remove nut and washer (1). 2. Disconnect nut fitting (3). 3. Remove oil level gauge (2) from oil…

3208

3208 INDUSTRIAL ENGINE – Oil Level Gauge

Posted on March 3, 2022 by sam

(1) Guide assembly. Assemble lower part of guide assembly (1) so that Point A is even with bottom surface of block within ± 0.8 mm…

3208

3208 INDUSTRIAL ENGINE – Oil Level Gauge

Posted on March 3, 2022 by sam

(1) Guide assembly. Assemble lower part of guide assembly (1) so that Point A is even with bottom surface of block within ± .03 in.…

Posts pagination

Previous Page Page 1 … Page 24 Page 25 Page 26 … Page 206 Next Page

Resources

  • About Me
  • Contact Us
  • Privacy Policy

Categories

  • 3126
  • 3126
  • 3208
  • 3306
  • 3406E
  • BX-2150
  • C15
  • C18
  • C7
  • Cat ID
  • D330
  • Delco 27SI
  • EL-740
  • Engine News
  • Programming
  • Service Magazine
  • Special Instruction
  • Troubleshooting
  • Uncategorized

Recent Posts

  • Cat C7 Injection Actuation Pressure Sensor Location
  • Programming – A/C Pressure Switch Fan-On Time
  • Programming – Minimum & Maximum Idle Shutdown Outside Temperature
  • Programming – Allow Idle Shutdown Override
  • Programming – Idle Shutdown Timer
© Copyright 2026 – Caterpillar Engines Troubleshooting
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy