Flywheel | Caterpillar Engines Troubleshooting

Tag Archives for flywheel

3116 and 3126 Truck Engines Bore Runout (Radial Eccentricity) Of The Flywheel

Checking Bore Runout Of The Flywheel (Typical Example) (1) 7H1945 Holding Rod (2) 7H1645 Holding Rod (3) 7H1942 Indicator (4) 7H1940 Universal Attachment 1. Install the dial indicator (3) and make an adjustment of the universal attachment (4) so it … Continue reading

26. July 2017 by sam
Categories: 3126 | Tags: , , , , | Leave a comment

3116 and 3126 Truck Engines Bore Runout (Radial Eccentricity) Of The Flywheel Housing

1. Fasten the dial indicator as shown so the anvil of the indicator will touch the bore of the flywheel housing. 2. With the dial indicator in position at (C), adjust the dial indicator to “0” (zero). Push the crankshaft … Continue reading

26. July 2017 by sam
Categories: 3126 | Tags: , , , , | Leave a comment

3116 and 3126 Truck Engines Face Run Out (Axial Eccentricity) Of The Flywheel Housing

8T5096 Dial Indicator Group Installed (Typical Example) If any method other than given here is used, always remember bearing clearance must be removed to get correct measurements. 1. Fasten a dial indicator to the flywheel so the anvil of the … Continue reading

26. July 2017 by sam
Categories: 3126 | Tags: , , , | Leave a comment

3116 and 3126 Truck Engines Flywheel Housing – Remove and Install

Removal Procedure Start By: A.Remove the flywheel. Refer to Disassembly and Assembly, “Flywheel – Remove”. 1.Fasten Tooling (A) and a suitable lifting device to flywheel housing (1) . 2.Remove bolts (2) and bolt (3) that fastens flywheel housing (1) to … Continue reading

17. July 2017 by sam
Categories: 3126 | Tags: , , , | Leave a comment

3116 and 3126 Truck Engines Flywheel Housing Bore

Typical Example NOTE: Write the dial indicator measurements with their positive (+) and negative (-) notation (signs). This notation is necessary for making the calculations in the chart correctly. 1. Fasten the dial indicator to the flywheel so the anvil … Continue reading

17. July 2017 by sam
Categories: 3126 | Tags: , , , | Leave a comment

3116 and 3126 Truck Engines Flywheel Housing Runout

Face Runout (Axial Eccentricity) Of The Flywheel Housing: 8T5096 Dial Indicator Group Installed (Typical Example) 1. Fasten a dial indicator to the crankshaft flange so the anvil of the indicator will touch the face of the flywheel housing. 2. Put … Continue reading

17. July 2017 by sam
Categories: 3126 | Tags: , , , | Leave a comment

3116 and 3126 Truck Engines Flywheel Housing

Typical Example See the topics, Flywheel Housing Runout and Flywheel Housing Bore, for the correct methods of flywheel housing inspection. NOTE: Apply 1U8846 Gasket Maker to the entire cylinder block mounting face of the flywheel housing before assembling the flywheel … Continue reading

17. July 2017 by sam
Categories: 3126 | Tags: , , , | Leave a comment

3116 and 3126 Truck Engines Flywheel – Install

Installation Procedure Note: For information on the reusability of the flywheel on 3116 engines, refer to Guideline For Reusable Parts And Salvage Operations, SEBF8207, “Flywheel Specifications for 3116 Engines”. Note: Drill and tap the new flywheel ring gear if the … Continue reading

17. July 2017 by sam
Categories: 3126 | Tags: , , | Leave a comment

3116 and 3126 Truck Engines Flywheel – Remove

Removal Procedure Table 1 Required Tools     Tool     Part Number     Part Description     Qty     A     138-7573     Link Bracket     2     B     –   … Continue reading

17. July 2017 by sam
Categories: 3126 | Tags: , , | Leave a comment

3116 and 3126 Truck Engines Flywheel Runout

Face Runout (Axial Eccentricity) Of The Flywheel: Checking Face Runout Of The Flywheel (Typical Example) 1. Install the dial indicator as shown. Put a force on the flywheel toward the rear. 2. Set the dial indicator to read 0.0 mm … Continue reading

17. July 2017 by sam
Categories: 3126 | Tags: , , | Leave a comment

← Older posts