Caterpillar Engines Troubleshooting

Cat Engines Maintenance & Repair Guides

Skip to content
Menu
  • Home
  • Contact Us
  • Privacy Policy

Category: C7

C7

C7 Industrial Engines Systems Operation – Fuel System

Posted on November 24, 2020 by sam

Introduction Illustration 1 g01447542 Fuel System Diagram (1) Unit injector hydraulic pump (2) Oil flow to engine (3) Oil filter (4) Engine oil pump (5)…

C7

C7 Industrial Engines Systems Operation – Electronic Control System Components

Posted on November 24, 2020 by sam

Illustration 1 g01447503 Electronic control System components (left side view) (1) Connector for the injection actuation pressure control valve (2) Injection actuation pressure sensor (3)…

C7

C7 Industrial Engines Systems Operation – General Information

Posted on November 24, 2020 by sam

Right side view (1) Lifting eye (2) Water drain plug (3) Exhaust manifold (4) Turbocharger (5) Alternator (6) Orifice for bleeding the wastegate (if equipped)…

C7

C7 Industrial Engines Systems Operation – Engine Design

Posted on November 24, 2020 by sam

Cylinder And Valve Location (A) Exhaust valve. (B) Inlet valve. Bore … 110 mm (4.3 inch) Stroke … 127 mm (5.0 inch) Displacement … 7.25…

C7

C7 Industrial Engines Specifications – Air Inlet Heater

Posted on November 24, 2020 by sam

(1) Nut Tighten the nut to the following torque. … 8 ± 1 N·m (70 ± 9 lb in) Note: Do not switch the positive wire…

C7

C7 Industrial Engines Specifications – Engine Oil Pressure Sensor

Posted on November 24, 2020 by sam

Table 1 Specification for the 161-1705 Engine Oil Pressure Sensor  Item Qty Part Specification Description 1 – – Torque the pressure sensor to 10 ± 2 N·m…

C7

C7 Industrial Engines Specifications – Coolant Level Sensor

Posted on November 24, 2020 by sam

(1) Final installation torque for the liquid level sensor group … 22 ± 3 N·m (16 ± 2 lb ft) Operating temperature … -40 to…

C7

C7 Industrial Engines Specifications – Coolant Temperature Sensor

Posted on November 24, 2020 by sam

Table 1 Specification for 130-9811 Temperature Sensor Gp , 274-7396 Temperature Sensor Gp , 197-8392 Temperature Sensor Gp, and 256-6453 Temperature Sensor  Item Qty Part Specification Description 1 1 – Torque to 20…

C7

C7 Industrial Engines Specifications – Magnetic Pickup

Posted on November 24, 2020 by sam

While the engine is stopped, install the magnetic pickup. Once the magnetic pickup is in contact with the flywheel ring gear, turn the magnetic pickup…

C7

C7 Industrial Engines Specifications – Electric Starting Motor

Posted on November 24, 2020 by sam

S/N – JRA1-UP S/N – JTF1-UP When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ……

Posts navigation

Page 1 Page 2 … Page 23 Next Page

Resources

  • Contact Us
  • Privacy Policy

Categories

  • 3126
  • 3126
  • 3208
  • 3208
  • 3306
  • 3406E
  • BX-2150
  • C18
  • C7
  • Cat ID
  • D330
  • Delco 27SI
  • EL-740
  • Engine News
  • Service Magazine
  • Special Instruction
  • Troubleshooting
  • Uncategorized

Recent Posts

  • 3406E and 3456 Industrial Engines Testing and Adjusting – Cooling System – Test
  • 3406E and 3456 Industrial Engines Testing and Adjusting – Cooling System – Inspect
  • 3406E and 3456 Industrial Engines Testing and Adjusting – Cooling System – Check – Overheating
  • 3406E and 3456 Industrial Engines Testing and Adjusting – Increased Engine Oil Temperature – Inspect
  • 3406E and 3456 Industrial Engines Testing and Adjusting – Excessive Engine Oil Consumption – Inspect
© Copyright 2021 – Caterpillar Engines Troubleshooting
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy