Caterpillar Engines Troubleshooting

Cat Engines Maintenance & Repair Guides

Skip to content
Menu
  • Home
  • Contact Us
  • Privacy Policy

Category: C18

C18

C7 Industrial Engines Testing and Adjusting – Inlet Manifold Pressure – Test

Posted on October 21, 2020 by sam

The efficiency of an engine can be checked by making a comparison of the pressure in the inlet manifold with the information given in the…

C18

C13, C15, and C18 Engines Troubleshooting – Timing – Calibrate

Posted on October 20, 2020 by sam

Table 1 Diagnostic Trouble Codes CDL Code J1939 Code Code Description (code descriptions may vary) Comments 261-11 637-11 Engine Timing Offset fault The wiring to…

C18

C13, C15, and C18 Engines Troubleshooting – Cooling Fan – Calibrate

Posted on October 20, 2020 by sam

Use this procedure if the diagnostic code in Table 1 is active. Table 1 Diagnostic Trouble Codes CDL Code J1939 Code Code Description (code descriptions…

C18

C13, C15, and C18 Engines Troubleshooting – Electrical Connectors – Inspect

Posted on October 20, 2020 by sam

Most electrical faults are caused by poor connections. The following procedure will assist in detecting faults with connectors and with wiring. If a fault is…

C18

C13, C15, and C18 Engines Troubleshooting – ARD Combustion Air Valve – Replace

Posted on October 20, 2020 by sam

This code will trip if the automated ARD Air Valve Calibration sweep exceeds the calibration limits AND a failed regeneration occurs. The ARD Air Valve calibration is…

C18

C13, C15, and C18 Engines Troubleshooting – ECM – Replace

Posted on October 20, 2020 by sam

The Engine Control Module (ECM) contains no moving parts. Replacement of the ECM can be costly. Replacement can also be a time consuming task. Follow…

C18

C13, C15, and C18 Engines Troubleshooting – ECM Software – Install

Posted on October 20, 2020 by sam

Use this procedure to troubleshoot the electrical system if the diagnostic code in Table 1 is active. Table 1 Diagnostic Trouble Codes CDL Code J1939…

C18

C13, C15, and C18 Engines Troubleshooting – Injector Trim File – Install

Posted on October 20, 2020 by sam

The Caterpillar Electronic Technician (ET) is used to load injector trim files into the Engine Control Module (ECM). Injector trim files are available from these…

C18

C13, C15, and C18 Engines Troubleshooting – Test ECM Mode

Posted on October 20, 2020 by sam

“Test ECM Mode” is a feature in the software that can be used to help troubleshoot an engine that may have a fault in the…

C18

C13, C15, and C18 Engines Troubleshooting – Factory Passwords

Posted on October 20, 2020 by sam

Note: Factory passwords are only available to service technicians from an authorized Caterpillar Dealership. Customers of Caterpillar do not have access to the Caterpillar Factory Password…

Posts navigation

Page 1 Page 2 … Page 20 Next Page

Resources

  • Contact Us
  • Privacy Policy

Categories

  • 3126
  • 3126
  • 3208
  • 3306
  • 3406E
  • BX-2150
  • C15
  • C18
  • C7
  • Cat ID
  • D330
  • Delco 27SI
  • EL-740
  • Engine News
  • Service Magazine
  • Special Instruction
  • Troubleshooting
  • Uncategorized

Recent Posts

  • C-15 and C-16 Industrial Engines – Pinion Clearance – Adjust
  • C-15 and C-16 Industrial Engines – Pinion Clearance – Adjust
  • C-15 and C-16 Industrial Engines – Electric Starting System – Test
  • C-15 and C-16 Industrial Engines – Charging System – Test
  • C-15 and C-16 Industrial Engines – Battery – Test
© Copyright 2023 – Caterpillar Engines Troubleshooting
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy