Caterpillar Engines Troubleshooting

Cat Engines Maintenance & Repair Guides

Skip to content
Menu
  • Home
  • Contact Us
  • Privacy Policy

Category: 3406E

3406E

3406E and 3456 Industrial Engines – Turbocharger

Posted on May 29, 2021 by sam

Remove & Install Turbocharger Fluid Spillage Containment Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and…

3406E

3406E and 3456 Industrial Engines – Turbocharger

Posted on May 29, 2021 by sam

Illustration 1 g00288169 Typical example (1) Tighten the clamp bolts to the following torque. … 14 ± 3 N·m (10 ± 2 lb ft) Lightly…

3406E

3406E and 3456 Industrial Engines – Exhaust Manifold

Posted on May 29, 2021 by sam

Remove & Install Exhaust Manifold Start By: a. remove turbocharger b. remove water regulator housing 1. Remove the nuts and spacers (1), and remove exhaust…

3406E

3406E and 3456 Industrial Engines – Exhaust Manifold

Posted on May 29, 2021 by sam

Illustration 1 g00284845 Typical example (1) A thin film of 2P-2333 High Temperature Sealer is applied to the outside diameter of the male end of…

3406E

3406E and 3456 Industrial Engines – Rocker Arm & Shaft Assemblies

Posted on May 29, 2021 by sam

Remove & Install Rocker Arm & Shaft Assemblies Start By: a. remove the valve cover(s) Valve rocker arms (1) and unit injector rocker arms (2)…

3406E

3406E and 3456 Industrial Engines – Valve Cover Base

Posted on May 29, 2021 by sam

Remove & Install Valve Cover Base Start By: a. remove valve covers 1. Loosen the two nuts and remove connector (2) from electronic unit injector…

3406E

3406E and 3456 Industrial Engines – Valve Covers

Posted on May 29, 2021 by sam

Remove & Install Valve Covers Fluid Spillage Containment Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting…

3406E

3406E and 3456 Industrial Engines – Valve Mechanism Cover

Posted on May 29, 2021 by sam

Illustration 1 g01431260 Typical Example Illustration 2 g00285630 Tightening Sequence For Valve Cover And Base Note: Apply 4C-4030 Thread Lock Compound to the bolts that…

3406E

3406E and 3456 Industrial Engines – Valve Mechanism

Posted on May 25, 2021 by sam

Illustration 1 g00859782 (1) Valve rocker arm assembly (2) Valve lash Inlet valves … 0.38 ± 0.08 mm (0.015 ± 0.003 inch) Exhaust valves ……

3406E

3406E and 3456 Industrial Engines – Rocker Shaft

Posted on May 25, 2021 by sam

Illustration 1 g00287811 (1) Ball (2) Diameter of rocker arm shaft … 40.000 ± 0.010 mm (1.5748 ± 0.0004 inch)

Posts navigation

Page 1 Page 2 … Page 33 Next Page

Resources

  • Contact Us
  • Privacy Policy

Categories

  • 3126
  • 3126
  • 3208
  • 3306
  • 3406E
  • BX-2150
  • C15
  • C18
  • C7
  • Cat ID
  • D330
  • Delco 27SI
  • EL-740
  • Engine News
  • Service Magazine
  • Special Instruction
  • Troubleshooting
  • Uncategorized

Recent Posts

  • C-10, C-12, C-15 and C-16 Industrial Engines – Maintenance Due Lamp Circuit – Test
  • C-10, C-12, C-15 and C-16 Industrial Engines – Injector Solenoid Circuit – Test
  • C-10, C-12, C-15 and C-16 Industrial Engines – Ether Injection System – Test
  • C-10, C-12, C-15 and C-16 Industrial Engines – Engine Temperature Sensor Open or Short Circuit – Tes
  • C-10, C-12, C-15 and C-16 Industrial Engines – Engine Speed/Timing Sensor Circuit – Test
© Copyright 2022 – Caterpillar Engines Troubleshooting
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy