Caterpillar Engines Troubleshooting

Cat Engines Maintenance & Repair Guides

Skip to content
Menu
  • Home
  • Contact Us
  • Privacy Policy

Category: 3208

3208

3208 INDUSTRIAL ENGINE – Gauge For Engine Oil Pressure 2N781 Gauge; Use with 2N782 Sending Unit.

Posted on March 3, 2022 by sam

Rating … 12V Pressure range … 0 to 120 psi(0 to 830 kPa) Calibration test at 14V (30° mounting): 0 psi (0 kPa) … 240…

3208

3208 INDUSTRIAL ENGINE – Oil Level Gauge

Posted on March 3, 2022 by sam

Remove & Install Oil Level Gauge 1. Remove nut and washer (1). 2. Disconnect nut fitting (3). 3. Remove oil level gauge (2) from oil…

3208

3208 INDUSTRIAL ENGINE – Oil Level Gauge

Posted on March 3, 2022 by sam

(1) Guide assembly. Assemble lower part of guide assembly (1) so that Point A is even with bottom surface of block within ± 0.8 mm…

3208

3208 INDUSTRIAL ENGINE – Oil Level Gauge

Posted on March 3, 2022 by sam

(1) Guide assembly. Assemble lower part of guide assembly (1) so that Point A is even with bottom surface of block within ± .03 in.…

3208

3208 INDUSTRIAL ENGINE – Water Separator

Posted on March 3, 2022 by sam

Remove Water Separator NOTICE Element (2) is free to fall when clamp (1) is released. 1. Remove clamp (1) and element (2). 2. Disconnect line…

3208

3208 INDUSTRIAL ENGINE – Fuel Injection Nozzles

Posted on March 3, 2022 by sam

Remove Fuel Injection Nozzles start by: a) remove rocker shafts 1. Thoroughly clean the area around each fuel line connection. Disconnect fuel injection line (1)…

3208

3208 INDUSTRIAL ENGINE – Fuel Injection Lines

Posted on March 3, 2022 by sam

Remove Fuel Injection Lines 1. Disconnect lines (1) and (2). 2. Remove bolt (3) from the bracket. 3. Loosen nuts (4) at the cylinder head…

3208

3208 INDUSTRIAL ENGINE – Fuel Injection Nozzles

Posted on March 3, 2022 by sam

122-9007 (1) Torque for valve lift locknut … 4 to 5 N·m (35 to 45 lb in) (2) Torque for pressure screw locknut … 8.0…

3208

3208 INDUSTRIAL ENGINE – Injection Nozzle (9N3979 and 1W5829)

Posted on February 22, 2022 by sam

Bench test nozzles using clean SAE J967 Calibration Oil (Kent-Moore Corp. J-26400 or Viscor Calibration Fluid 1487C-SAE J-967C) at a temperature of … 65 to…

3208

3208 INDUSTRIAL ENGINE – Fuel Injection Pumps

Posted on February 22, 2022 by sam

Remove Fuel Injection Pumps Start By: a. remove fuel injection lines b. remove shutoff housing, check valve and bypass valve Fluid Spillage Containment Care must…

Posts navigation

Previous Page Page 1 Page 2 Page 3 … Page 30 Next Page

Resources

  • Contact Us
  • Privacy Policy

Categories

  • 3126
  • 3126
  • 3208
  • 3306
  • 3406E
  • BX-2150
  • C15
  • C18
  • C7
  • Cat ID
  • D330
  • Delco 27SI
  • EL-740
  • Engine News
  • Service Magazine
  • Special Instruction
  • Troubleshooting
  • Uncategorized

Recent Posts

  • C-15 and C-16 Industrial Engines – Main Bearings – Inspect
  • C-15 and C-16 Industrial Engines – Connecting Rod Bearings – Inspect
  • C-15 and C-16 Industrial Engines – Piston Ring Groove – Inspect
  • C-15 and C-16 Industrial Engines – Water Pump – Test
  • C-15 and C-16 Industrial Engines – Water Temperature Regulator – Test
© Copyright 2022 – Caterpillar Engines Troubleshooting
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy