Category Archives for 3126

3100 HEUI Truck Engine Installation Fuel Tank Assembly

(1) Bolt. These bolts secure the fuel tank assembly to the Base assembly. For more information please refer to Base Assembly in this publication. A. Length (from outer edge to bolt hole centerline on the top of fuel tank assembly) … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3100 HEUI Truck Engine Installation Engine Supports

Left Side View Right Side View (1) Left rear support. Use four bolts for attaching to the engine and use one bolt for attachment to the frame assembly (2). (2) Frame assembly (3) Junction box. For more information please refer … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3100 HEUI Truck Engine Installation Battery Support

Rear View (1) 25.4 mm (1.000 in) by 25.4 mm (1.000 in) angle iron support. For more information please refer to Fuel Tank Assembly in this publication. A. Length (between bolt hole centerlines) … 351 mm (13.818 in) B. Angle … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3100 HEUI Truck Engine Installation Base Assembly

  (1) Fork lift channels. (2) Bolt holes for fuel tank assembly. For more information please refer to Fuel Tank Assembly in this publication. (3) Base assembly. A. Length (from outside bolt hole centerline to bolt hole centerline) … 148 … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3100 HEUI Truck Engine Installation Alternator Pulley Shield

Right Side View (1) Alternator Pulley Shield. Assemble to belt guard (3) with two bolts, four washers, and two locknuts. A. Length (from edge to bolt hole centerline) … 43 mm (1.692 in) B. Length (from bolt hole centerline to … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3100 HEUI Truck Engine Installation Inlet Air Elbow Assembly

(1) Air intake assembly. (2) 100-8302 gasket. NOTE: Remove any gasket maker that remains on the inlet air heater. (3) Air intake plate. (4) Wrapper end plates. (5) Angle for the wrapper end plates (4) … 42 degrees (6) Vertical … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3100 HEUI Truck Engine Installation Air Cleaner Support

(1) Front Bracket. (2) Support Plate. Bolt to the air cleaner mounting group (3). (3) 4P3439 Air Cleaner Mounting Group. Attaches to the right hand side of the inlet air manifold. (4) Rear Bracket. Assembly procedure: 1. Fabricate the brackets … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3100 HEUI Truck Engine Installation General Description

Left Side View (1) Remote box. (2) Air cleaner. (3) Exhaust muffler. (4) Radiator. (5) Junction box. (6) Air compressor. (7) Battery. (8) Suction fan. (9) Base assembly. (10) Starter. (11) Support (left side). (12) Fuel tank. Right Side View … Continue reading

06. August 2017 by sam
Categories: 3126 | Leave a comment

3116 and 3126 Truck Engines Failures Oil Quality

Varnished oil can accumulate on the valve stem near the bottom of the valve guides’ contact. This accumulation of varnish is similar to the happenings of valves at high temperature. The buildup of varnish can cause the valve to stick … Continue reading

29. July 2017 by sam
Categories: 3126 | Tags: , , , | Leave a comment

3116 and 3126 Truck Engines Failures High Temperature

Valves for engines that operate in an overheated system will typically have a narrow band of oil coking near the bottom area of the valve guides’ travel. Mild adhesive and/or abrasive wear may be present. Valves in overheated systems may … Continue reading

29. July 2017 by sam
Categories: 3126 | Tags: , , , , | Leave a comment

← Older posts